Call 08048985035 90% Response Rate

our range

Industrial Control Valves

Pioneers in the industry, we offer pneumatic on off control valve, globe valve, pneumatic control ball valve, thermic fluid control valve, flow control valve and ibr globe control valve from India.
Pneumatic On Off Control Valve

Pneumatic On Off Control Valve

Rs 5,000  / PieceGet Best Price

Minimum Order Quantity: 1 Piece

End ConnectionScrewed End / Flanged End
BrandRegent
Actuation TypeDouble Acting / Single Acting
Valve BodyCF8 / CF8M / CF3M
Operating Pressure4.5 to 7 BAR
Size Range1/2 to 4 inch
2/3 way Mixing/Diverting Screwed Pneumatic On-Off Control Valve.

View Complete details

get quote request a call back
Globe Valve

Globe Valve

Rs 2,000  / PieceGet Best Price

Minimum Order Quantity: 1 Piece

Face To FaceASME B 16.10
Design StandardBS 1873
Testing StandardAPI 598 / BS EN 12266 -1
Flanged EndASME B 16.5
Butt Weld EndASME B 16.25
Pressure TemperatureASME B 16.34
OperatorHand wheel,Gear Operator
Size Range2 to 12 inch
We manufacture a wide range of Globe Valves which includes seal globe valves, gate globe valves and cast iron globe.

Regent Globe Valves are O.S. & Y Type i.e. outside screw & yoke, Bolted bonnet, & Rising stem. Globe valves are used where throttling and both throttling and shut-off is required. They can also be used for on-off service, but because of high pressure drop, this is generally confined to applications where the valve is normally closed and drop is not important when the valve is open. Normally globe valves are installed with flow under the disc, but under certain conditions flow over the disc may have the advantages.


Design Features:
  • Streamlined shaped body for smooth flow of the working fluid for minimum pressure Drop.
  • Back seating arrangement permits the replacement of packings while the valve is in full open position

Material Structure:

  • End Connection: Flanged end raised face, Butt weld end, RTJ, etc.
  • Operation : Hand wheel, Gear operator, Electrical Actuator, Pneumatic, Hydraulic
  • Shell : WCB, WC1, WC6, WC9, LCB, LCC, LC3, C5, C12, CF8, CF8M, CF3, CF3M, CF8C, CN7M, CD4MCu, Hastalloy, Inconel, Duplex Stainless Steel.
  • Trim : 13% Cr. Steel, 304, 304L, 316, 316L, 321, 347, Monel, Duplex Stainless steel.


Control Operation:Manual, Pneumatic, Electric

    View Complete details

    get quote request a call back
    • Pneumatic Control Ball Valve
    • Pneumatic Control Ball Valve
    Pneumatic Control Ball Valve

    Pneumatic Control Ball Valve

    Rs 6,500  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    Temperature of MediaHigh Temperature
    BrandRegent
    MaterialStainless Steel, Casting
    PressureUpto 10 Bar
    Size1/2 to 14 Inch
    End ConnectionScrewed End / Socket Weld / Triclover / Flanged End Class 150, 300
    Pneumatic Control Ball Valve:
    Standard Pneumatic Actuator Operated Investment Casting WCB/CF8/CF8M/CF3M Ball Valve in Three Piece design,engineered for Multiple On/Off operations in the down stream

    Size Range: 1/2" to 10" Screwed/Flanged/Tri Clover/Socket Weld

    Acessories:
    • On/Off Indicator
    • Namur Standard Solenoid Valve in all Standard Coil Voltage
    • Pneumatic & Electropneumatic Valve Positioner
    • Deluctchable Manual Over-ride
    • Limit Switches for On/Off Indication at Panel Board
    • Filter + Regulator Combination with Pressure Gauge
    • Air Lock Valve

    Standard:
    • Desing & Manufacturing : ASME B 16.34/BS EN ISO 17292/ API -6D
    • Valve Face to Face Dimension : ASME B 16.10
    • Flange Standard Conformity : ASME B 16.5 Class 150,Class 300
    • Inspection & Testing : API 598/ FCI-70-2/BS EN 12266-1/API-6D

    View Complete details

    get quote request a call back
    Thermic Fluid Control Valve

    Thermic Fluid Control Valve

    Rs 6,000  / PieceGet Best Price
    ModelRD3
    Size15 mm to 200 mm
    BodyASTM A216 Gr. WCB/ASTM A351 Gr. CF8/CF8M
    End ConnectionsFlanged Ends ANSI B16.5 Cl.150, Cl. 300, PN 16 & PN25 (600 available on request)
    Pressure RatingANSI B16.5 Cl.150, Cl. 300
    Temperature RatingMax 400 degree C
    Gland PackingTeflon/Grafoil
    SeatMetal Seated
    MaterialS.S. 304, S.S. 410
    ActuatorDiaphragm type Single Acting
    DiaphragmNylon inserted high nitrile, roll form type
    FluidHot thermic fluid, hot water, steam, oil, gas
    Thermic Fluid Control Valve:
    3 way Diaphragm operated Pneumatic Control Valve for Mixing/Diverting Duty.

    Accessories:
    • Electro Pneumatic Valve Positioner
    • Modulating Controller: 4-20mA PID Controller (Available on Request)


    Additional Information:

    • Item Code: RD4

    View Complete details

    get quote request a call back
    Flow Control Valve

    Flow Control Valve

    Rs 5,000  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    Size1/2 To 12inch
    TypeFlow Control Valve
    BrandRegent
    MaterialCast Steel
    Actuator TypeMulti Action
    A Flow control valve regulates the flow or pressure of a fluid. Control valves normally respond to signals generated by independent devices such as flow meters or temperature gauges.Control valves are normally fitted with actuators and positioners. Pneumatically-actuated flow control valve regulates the flow or pressure of a fluid.
    The most common final control element in the process control industries is the control valve. The control valve manipulates a flowing fluid, such as gas, steam, water, or chemical compounds, to compensate for the load disturbance and keep the regulated process variable as close as possible to the desired set point.

    View Complete details

    get quote request a call back
    Ibr Globe Control Valve

    Ibr Globe Control Valve

    Rs 12,000  / NumberGet Best Price

    Minimum Order Quantity: 1 Number

    Product Brochure

    MaterialStainless Steel
    BrandREGENT
    Usage/ApplicationIndustrial
    PressureHigh Pressure
    Valve Size25MM TO 300MM
    Valve TypeNC / NP
    Body StyleGlobe Type
    Connection TypeFLANGED / BUTTWELD
    PowerPNEUMATIC/MOTORISED
    Diameter25 TO 300
    Flow RateMIN TO MAX
    Actuator TypePNEUMATIC / MOTORISED
    Temperature0-350 DEGREE
    ColorBlack
    DesignGLOBE TYPE
    Fluid MediaSTEAM
    Model Name/NumberRDIBR
    Material GradeCS
    EnclosureWEATHER PROOF
    End ConnectionFLANGED
    Warranty1 YEAR
    I Deal InNew Only
    IBR GLOBE CONTROL VALVE FOR STEAM CONTROL APPLICATION

    View Complete details

    get quote request a call back
    Angle Type Control Valve

    Angle Type Control Valve

    Rs 1,500  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    Port Size1/2 to 2 inch BSP/NPT
    Body and SleeveSS ASTM A351 Grade CF8/CF8M
    End ConnectionScrewed/ Flange
    Max Working Pressure0 bar to 16 bar
    Pnem Pressure3.5 to 7 bar.
    ShaftSS-304 / SS-316
    SeatTeflon Optional Viton/EPDM
    Seal and O RingViton, EPDM, NBR.
    Orifice16.00 mm
    Fluid Temp-10 degree C to 180 degree C
    Ambient Temp-10 degree C to 60 degree C
    MediaAir, Water, Steam, Gas, Oil, Fuel, Liquid, Vacuum
    Actuator CoverSS-304
    Actuator FlangeAluminum Die Cast (Hard Anodised)
    Actuator Working pressure3.5 to 7 bar
    With enormous experience in this domain, we have established ourselves as the dependable manufacturer, exporter and supplier of excellent quality Angle Type Control Valve. This valve is manufactured from quality tested raw material and progressive technology. While manufacturing this valve, we lay special emphasis on its functioning and quality. The offered range is used to remote fluid and gases control applications. Clients can avail this valve from us at rock bottom prices.

    Features:
    • Accurate dimension
    • Sturdiness
    • Rust proof

    View Complete details

    get quote request a call back
    Process Control Valve

    Process Control Valve

    Rs 5,000  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    BrandRegent
    MaterialCarbon Steel /Alloy Steel
    Valve TypeGlobe Valve
    Connection TypeFlanged / Buttweld
    Size15 NB to 500 NB
    Fluid MediaWater, Gas, Air
    Max Tempertaure800 degree C
    Process Control Valve: A positioner is a device put into a valve to ensure that it is at a correct position of opening as per the control signal(4-20mA). An I/P converter only sends the opening/closing request to valve but cannot confirm its position.
    Positioner senses the valve opening through a position feedback link Connected to valve stem which is its input signal. I/P converter output is its set point input. The difference between these two is the error signal based on
    which the positioner positions the valve to correct position to reduce error to zero. Hence positioner is nothing but a pneumatic feedback controller. Controlled external supply air to positioner provides power to positioner to position a valve. Also positioner is used in a valve when valve operating signal range is different from I/P converter output range.
    The Electro pneumatic Valve positioners are the latest trends in control automation and REGENT has expertise in calibrating these equipment''s with proficiency to improve the productivity of its client.

    View Complete details

    get quote request a call back
    Pneumatic Cylinder Operated Control Valve

    Pneumatic Cylinder Operated Control Valve

    Rs 11,000  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    Size15 mm to 200 mm
    MaterialS.S. 304,S.S. 410
    BrandRegent
    Temperature RatingMax 400 degree C
    SeatMetal Seated
    BodyASTM A216 Gr. WCB/ASTM A351 Gr. CF8/CF8M
    Pneumatic Cylinder Operated Control Valve for Steam /Hot Water / Chilled Water Application.

    Accessories Optional:
    • PID Temperature Controller
    • Solenoid Valve 230 V AC/ 110 V AC / 12 V DC / 24 V DC
    • Manual Override



    Additional Information:

    • Item Code: RCY

    View Complete details

    get quote request a call back
    Gate Valve

    Gate Valve

    Rs 2,000  / PieceGet Best Price

    Minimum Order Quantity: 1 Piece

    End ConnectionFlanged end raised face, Butt weld end, RTJ
    Design StandardAPI 600
    Testing StandardAPI 598
    Face to FaceASME B 16.10
    Flanged EndASME B 16.5
    Butt Weld EndASME B 16.25
    Pressure TemperatureASME B 16.34
    OperatorHand wheel
    Size Range2 to 12 inch
    We manufacture a wide range of Gate Valves which include knife gate valves, cast iron gate valves and flangled gate valves.

    Gate Valves are Outside Screw & Yoke, Bolted bonnet & with Rising stem. The “STRAIGHT THROUGH BORE” design assures minimum turbulence, erosion and resistance to flow caused by pockets & recesses. Gate Valves are mainly used where minimum pressure drop is a requirement.

    Design Features:
    • Designed for exceptionally low pressure drop
    • Back seating arrangement permits the replacement of packing with valve under fully open condition
    • Two piece design of gland flange provides centralizing effect to the gland sleeve, thus producing a uniform clamping pressure on the packings.

    Material Structure:

    • End Connection: Flanged end raised face, Butt weld end, RTJ, etc.
    • Operation : Hand wheel, Gear operator, Electrical Actuator, Pneumatic, Hydraulic
    • Shell : WCB, WC1, WC6, WC9, LCB, LCC, LC3, C5, C12, CF8, CF8M, CF3, CF3M, CF8C, CN7M, CD4MCu,Inconel, Duplex Stainless Steel.
    • Trim : 13% Cr. Steel, 304, 304L, 316, 316L, 321, 347, Monel, Duplex Stainless steel.


    Control Operation:Manual, Pneumatic, Electric

      View Complete details

      get quote request a call back
      Forged Steel Valve

      Forged Steel Valve

      Rs 1,200  / PieceGet Best Price

      Minimum Order Quantity: 1 Piece

      Driven TypeMANUAL / AUTOMATIC
      ConditionNew
      Surface FinishingYES
      ModelRFSV
      Class Rating800
      MaterialStainless Steel
      Weight10
      Stainless Steel GradeASTM A 105
      PressureClass 800
      Automation GradeSemi-Automatic
      ColorBlack
      Size15
      Quantity Per Pack20
      Max Tempertaure500 degree C


      Additional Information:

      • Item Code: RFSV1
      • Production Capacity: 10000
      • Delivery Time: 1 DAY

      View Complete details

      get quote request a call back
      Check Valves

      Check Valves

      Rs 2,000  / PieceGet Best Price

      Minimum Order Quantity: 1 Piece

      Design StandardBS 1868/API-6D
      Testing StandardAPI 598/BS EN 12266 -1
      Face to FaceASME B 16.10
      Flanged EndASME B 16.5
      Butt Weld EndASME B 16.25
      Pressure TemperatureASME B 16.34

      We manufacture a wide range of Check Valves which includes swing check valves, ball check valves and many more valves.

      Swing Check Valves are having Bolted cover, Swing type disc. These valves are used to prevent flow reversal in piping systems. They are suitable for service in horizontal (flow up through valve only) piping runs. Swing Check Valves have low pressure drop and are best suited for moderate velocity applications

      Swing Check Valves are suitable for all service media. Valves can also be supplied with counter weights and dash pot arrangement depending upon the condition and request.

       

      Material Structure:
      • End Connection: Flanged end raised face, Butt weld end, RTJ, etc.

      • Shell : WCB, WC1, WC6, WC9, LCB, LCC, LC3, C5, C12, CF8, CF8M, CF3, CF3M, CF8C, CN7M, CD4MCu, Hastalloy, Inconel, Duplex Stainless Steel.

      • Trim : 13% Cr. Steel, 304, 304L, 316, 316L, 321, 347, Monel, Duplex Stainless steel.

       

       

      View Complete details

      get quote request a call back

      EXPLORE MORE CATEGORIES